ASME SA335 P5,P9,P11,P12,P22,P91,DIN 17175, EN 10216-2 HIGH-TEMP. SEAMLESS PIPE

ASME SA335 P5,P9,P11,P12,P22,P91,DIN 17175, EN 10216-2 HIGH-TEMP. SEAMLESS PIPE

Model No.︰-

Brand Name︰ASTM/ASME A335/SA335 P1,P2,P5,P9,P11,P22,P23,P91,P

Country of Origin︰-

Unit Price︰US $ 795 / MT

Minimum Order︰10 MT

Inquire Now

Product Description


ASTM A335/AME SA335 Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

Chemical Composition(%):

Grade UNS Designation Composition, %
Carbon Manganese Phosphorus, Sulfur Silicon Chromium Molybdenum Others
P1 K11522 0.10–0.20 0.30–0.80 0.025 max 0.025 max 0.10–0.50 --- 0.44–0.65 ---
P2 K11547 0.10–0.20 0.30–0.61 0.025 max 0.025 max 0.10–0.30 0.50–0.81 0.44–0.65 ---
P5 K41545 0.15 max 0.30–0.60 0.025 max 0.025 max 0.50 max 4.00–6.00 0.45–0.65 ---
P9 S50400 0.15 max 0.30–0.60 0.025 max 0.025 max 0.25–1.00 8.00–10.00 0.90–1.10 ---
P11 K11597 0.05–0.15 0.30–0.60 0.025 max 0.025 max 0.50–1.00 1.00–1.50 0.44–0.65 ---
P12 K11562 0.05–0.15 0.30–0.61 0.025 max 0.025 max 0.50 max 0.80–1.25 0.44–0.65 ---
P15 K11578 0.05–0.15 0.30–0.60 0.025 max 0.025 max  1.15–1.65 --- 0.44–0.65 ---
P21 K31545 0.05–0.15 0.30–0.60 0.025 max 0.025 max 0.50 max 2.65–3.35 0.80–1.06 ---
P22 K21590 0.05–0.15 0.30–0.60 0.025 max 0.025 max 0.50 max 1.90–2.60 0.87–1.13 ---
P23 K41650 0.04–0.10 0.10–0.60 0.03 0.01 0.50 max 1.90–2.60 0.05–0.30 V 0.20–0.30
Cb 0.02–0.08
B 0.0005–0.006
N 0.030 max
Al 0.030 max
W 1.45–1.75
P91 K91560 0.08–0.12 0.30–0.60 0.02 0.01 0.20–0.50 8.00–9.50 0.85–1.05 V 0.18–0.25
N 0.030–0.070
Ni 0.40 max
Al 0.04 max
Cb 0.06–0.10
P92 K92460 0.07–0.13 0.30–0.60 0.02 0.01 0.50 max 8.50–9.50 0.30–0.60 V 0.15–0.25
N 0.03–0.07
Ni 0.40 max
Al 0.04 max
Cb 0.04–0.09
W 1.5–2.00
B 0.001–0.006

                                           Mechanical Properties:

ASTM A335 Grade Tensile Strength Yield Strength Elongation % Hardness(HB)
ksi MPa ksi MPa Longitudinal Transverse
P1 55 380 30 205 30 20 -
P2 55 380 30 205 30 20 -
P5 60 415 30 205 30 20 -
P5b 60 415 30 205 30 20 -
P5c 60 415 30 205 30 20 -
P9 60 415 30 205 30 20 -
P11 60 415 30 205 30 20 -
P12 60 415 32 220 30 20 -
P15 60 415 30 205 30 20 -
P21 60 415 30 205 30 20 -
P22 60 415 30 205 30 20 -
P23 74 510 58 400 20 - -
P91 85 585 60 415 20 - ≤250
P92 90 620 64 440 20 - ≤250
P122 90 620 58 400 20 - ≤250
P911 90 620 64 400 20 - -

*All values are minimum unless otherwise specified.
*The specimen for elongation test shall be in the gauge length of 2 inches or 50 mm(or 4D).

 3.Heat Treatment Requirements

Grade

Heat Treatment Type
P5, P9, P11, and P22

Normalizing Temperature Range F [C]

Subcritical Annealing or Tempering
Temperature Range F [C]

P5 (b,c)

Full or Isothermal Anneal

 

 

 

Normalize and Temper

*****

1250 [675]

 

Subcritical Anneal (P5c only)

*****

1325 – 1375 [715 - 745]

P9

Full or Isothermal Anneal

 

 

 

Normalize and Temper

*****

1250 [675]

P11

Full or Isothermal Anneal

 

 

 

Normalize and Temper

*****

1200 [650]

P22

Full or Isothermal Anneal

 

 

 

Normalize and Temper

*****

1250 [675]

P91

Normalize and Temper

1900-1975 [1040 - 1080]

1350-1470 [730 - 800]

 

Quench and Temper

1900-1975 [1040 - 1080]

1350-1470 [730 - 800]

 

Mechanical Tests Specified

Transverse or Longitudinal Tension Test and Flattening Test, Hardness Test, or Bend Test
For material heat treated in a batch-type furnace, tests shall be made on 5% of the pipe from each treated lot. For small lots, at least one pipe shall be tested.
For material heat treated by the continuous process, tests shall be made on a sufficient number of pipe to constitute 5% of the lot, but in no case less than 2 pipe.

Notes for Hardness Test:
P91 shall not have a hardness not exceeding 250 HB/265 HV [25HRC].

Notes for Bend Test:
For pipe whose diameter exceeds NPS 25 and whose diameter to wall thickness ratio is 7.0 or less shall be subjected to the bend test instead of the flattening test.
Other pipe whose diameter equals or exceeds NPS 10 may be given the bend test in place of the flattening test subject to the approval of the purchaser.
The bend test specimens shall be bent at room temperature through 180 without cracking on the outside of the bent portion.

Hydrostatic Test

The inside diameter of the bend shall be 1 inch [25 mm].
Each length of pipe shall be Hydro tested, at option of manufacture nondestructive electric testing can be used.

Ordering Information

Orders for material under this specification should include the following, as required, to describe the desired material adequately:

Quantity

Feet, meters, or number of lengths

Name of material

Seamless Alloy Steel Pipe

Grade

P5, P9, P11, P22, P91

Manufacture

Hot-finished or cold-drawn

Size using one of the following:

NPS and Schedule Number

Outside Diameter and Nominal Wall Thickness

Outside Diameter and Minimum Wall Thickness

Inside Diameter and Nominal Wall Thickness

Inside Diameter and Minimum Wall Thickness

Length

Specific or Random

End Finish

Referenced Documents

  • A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe
  • E213 Practice for Ultrasonic Examination of Metal Pipe and Tubing
  • E309 Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation
  • E381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
  • E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
  • E570 Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products
  • B36.10M Welded and Seamless Wrought Steel Pipe
  • SAE J 1086 Practice for Numbering Metals and Alloys (UNS)
  • SNT-TC-1A Recommended Practice for Nondestructive Personnel Qualification and Certification

Product Image